4 Channel Data Logger GL2000

CAT III 600V Compatible High-voltage High-speed Measurements

GL2000 is a high-voltage isolated 4 channels data logger that corresponds to CAT III 600 V and up to 600 V rms measurement, all channel isolated simultaneously at 1 MS/s and high-speed sampling. It can measure of factory equipment and high voltage measurement.
The DP-581H thermal printer can be connected and data can be handed over on the spot. It makes prevent data falsification and prevent data tampering.
Inside, 4MW/ch internal RAM and 8GB internal flash memory. Outside, SD memory card and USB memory storage media according to the sampling interval and situation.

High speed 1 MS/s simultaneous sampling with isolated input

GL2000 is equipped with an isolated input mechanism to protect signals from interferences caused by noise from other channels. 16-bit A/D converter adopted to achieve hi-speed and hi-resolution measurement.

Simultaneous sampling

GL2000 utilizes simultaneous sampling to eliminate slowdown in sampling rate by using multiple A/D converters in simultaneous sampling method.

External sampling

Sampling of the logger is performed in sync with an external device using an external signal input.

Multifunction Input with CAT III Measurement Category

CAT III 600 V is compatible with measuring power supply circuit in an equipment that captures power directly from the distribution panel.

Measures abnormalities in a repeated waveform by effectively measuring the corresponding RMS value

In 1000 Vrms range, Crest Factor is up to 1.41
Maximum rated safety voltage: 600 V rms, Peak voltage: 850V
In other range, Crest Factor is up to 2.0

Large Easy-to-read 7-inch LCD

Y-T waveform monitor screen
Digital monitor screen
Past waveform monitor screen
XY graph monitor screen

Quick and Easy Set Up Process

Simple operation with cursor and enter keys, and menu-driven operation with six pre-set menu screens: AMP, DATA, DISP, TRIG, I/F (Interface) and OTHER.

Equipped with three types of options for power source

AC adapter
DC input
battery pack

Option

Storage case (B-581)

Supports Large Built-in RAM (4MS/ch) and Built-in Flash (8GB)

Built-in Flash memory

4 MW samples/ch built-in RAM
8 GB built-in Flash memory

External Storage

SD Card memory
USB Flash memory

Convenient Data Recording Functions

Memory division function
Ring / Relay mode
Save & replay data in CSV format
Data backup and hot swaps
Auto save function
Search function

Equipped with Ethernet (LAN) and USB Interface to Communicate with PC

Convenient function with LAN (Ethernet interface) capability

Web server function
FTP server function
NTP client function
Email sending function

USB Drive Mode to Easily Transfer Files to PC

USB drive mode

Scale : mm
Tolerance : +/- 3 mm

SENSOR & CABLE

click here

Main unit specifications
Input Specifications
Software specifications
Standard accessories
Battery pack B-569 (option) Specifications
Humidity Sensor B-530 (option) Specifications
Dimensions

Main unit specifications

スクロールできます

Item			Description
Display (LCD)	Size		7-inch TFT color LCD (WVGA: 800 x 480 dots)
	Information		Waveform in Y-T with digital values, Enlarged waveforms, Digital values and Real-time statistical result values, XY graph
	Language		English, French, German, Spanish, Russian, Chinese, Korean, Japanese
Interface to PC	Type		Ethernet (10 BASE-T/100 BASE-TX), USB2.0
	Function		Data transfer to PC (up to 1 ms sampling), Control command to GL2000
	Ethernet functions		Web server function, FTP server function, NTP client function, DHCP client function, Email send function
	USB function		USB mode (File transfer and deletion from built-in flash and SD on GL2000)
Trigger function	Trigger action		Start or stop capturing data by triggering
	Trigger source		• Start: Off, Measured signal, Alarm, External, Scheduled time, Scheduled day, Elapsed time • Stop: Off, Measured signal, Alarm, External, Scheduled time, Scheduled day, Elapsed time
	Trigger source
	Combination		Level OR, Level AND, Edge OR, Edge AND
	Threshold		• Analog (*1): High or Low in level mode, Rising or Falling in edge mode, Window-in, Window-out • Logic: H or L (4-channel signal pattern) • Pulse: High or Rising, Low or Falling, Window-in, Window-out


Storage deice	Built-in RAM		Four million samples for each channel • Memory partition: 4 M samples x 1 bank, 2 M sample x 2 banks, 1 M samples x 4 banks, 500 k samples x 8 banks • Capturing data points: Specified 10 to 4000000 • Data type: Captured data • Auto-save: Transfer captured data to other devices after capturing is completed (It can be enabled or disabled)
	Built-in Flash		8GB • Data type: Captured data, Condition settings, Screen copy
	*External USB (2)**		Support USB Flash memory device (*3) by USB2.0 Type A port, Single port, No memory capacity limit • Data type: Captured data, Condition settings, Screen copy
	External *SD CARD (2)**		Support SDHC memory card (up to 32 GB) by SD Card slot, Single slot • Data type: Captured data, Condition settings, Screen copy
	Capturing mode	Off (Normal)	Save data between start to stop
		*Ring (4)**	Save most recent data of specified number • Destination: Built-in RAM, Built-in Flash, USB or SD • Number of capturing data: 1000 to 10000000 data (*5) • Sampling: up to 1 MS/s (interval 1 μs) in built-in RAM, up to 1 kS/s (interval 1 ms) with GBD format in other device, up to 100 S/s (interval 10 ms) with CSV format in other device
		Relay	Save data to multiple files with specified capturing time or file size (up to 4 GB) until recording data is stopped • Destination: Built-in Flash, USB or SD • Sampling: up to 1 kS/s (interval 1 ms) with GBD format, up to 100 S/s (interval 10 ms) with CSV format
	Data backup	*Interval (6)**	Off, 1, 2, 6, 12, 24 hrs., specific time, or any time with key operation • Sampling: up to 1 kS/s (interval 1 ms) with GBD format, up to 100 S/s (interval 10 ms) with CSV format
		*File destination (6)**	Built-in Flash, USB or SD, FTP
		*Data format (6)**	GBD (binary) or CSV (test)
		Hot-swapping external memory	Hot-swapping USB or SD Flash memory with key operation during data backup
Calculation function	Statistical		Real-time: Display digital and statistical values at the same time • Function: Maximum, Minimum, Peak-to-peak (P-P), Average
	Statistical		Replay: Statistical values between cursors in replay captured data • Function: Maximum, Minimum, Peak-to-peak (P-P), Average, RMS
	Between channels		Addition, subtraction, multiplication and division for two analog inputs (only in GBD format)
Operating environment			0 to 40 ºC when driven by AC adapter or battery, 5 to 85 % RH (non condensed)
Size			7-inch TFT color LCD (WVGA: 800 x 480 dots)
Power source			AC adapter: 100 to 240 V AC, 50/60 Hz DC power: 8.5 to 24 V DC (required cable option B-514) Battery pack: Two battery packs (option B-569) required


Power consumption	AC adapter (in 240 V AC)		Approx. 39 VA (59 VA while charging battery) with disabling screen saver Approx. 34 VA (55 VA while charging battery) with enabling screen saver
	DC drive (24 V)		Approx. 0.5 A (0.81 A while charging battery) with disable screen saver Approx. 0.43 A (0.76 A while charging battery) with enabling screen saver
	DC drive (12 V)		Approx. 1 A (Cannot charge battery) with disable screen saver Approx. 0.85 A (Cannot charge battery) with enabling screen saver
	DC drive (8.5 V)		Approx. 1.46 A (Cannot charge battery) with disable screen saver Approx. 1.22 A (Cannot charge battery) with enabling screen saver
External dimensions [W×H×D]			Approx. 260 x 161 x 83 mm (with the cover)
Weight			Approx. 1.7 kg (the cover is attached, AC adapter and battery are not included)
Vibration resistance			Compatible with JIS Vibration test method for automobile Type 1 Class A (Vibration durability test: 5 m/s²)

It can set for each channel.
File size of captured data is up to 4GB in each file.
Standard USB memory devices are required.
Required minimum capturing time is 15 seconds in GBD format, 30 seconds with CSV format.
When using built-in RAM, 10 to 4000000 data
* The CSV format and FTP server are available with firmware version 1.14 or rater.
– When the RING mode or external pulse synchronization sampling is selected for recording, the backup function is not available.
– When there are meany number of active channels, the sampling time is fast, or the backup interval is long, it may take time to closing the data file after recording stops because the size of the data to be backed up becomes large.
– When backup is enabled and data file format is specified with CSV format, SD memory card exchange (hot-swapping) and RELAY recording are not available.

Input Specifications

スクロールできます

Item			Description
Analog input specifications	Number of input channels		8 channels
	Type of input terminal		Isolated BNC connector and Screw terminal (M3.5 screw)
	Input method		All channels isolated unbalanced input, Simultaneous sampling
	Sampling speed (interval)		1 M Samples/s to 1 Sample/min (1 μs to 1 min) and External • Sampling interval: 1, 2, 5, 10, 20, 50, 100, 200, 500 μs, 1, 2, 5, 10, 20, 50, 100, 200, 500 ms, 1, 2, 5, 10, 20, 30 sec, 1 min * When using built-in RAM: 1 μs to 1 min, using other storage: 1 ms to 1 min
	Frequency response		DC ～ 200 kHz(+1 / -4dB)
	Measurement range	Voltage (DC)	20, 50, 100, 200, 500 mV 1, 2, 5, 10, 20, 50, 100, 200, 500V, 1-5V F.S.
		DC-RMS (DC coupling and rms value meas.)	10, 25, 50, 100, 250, 500 mV rms, 1, 2.5, 5, 10, 25, 50, 100, 250 V rms F.S. • Crest Factor: up to 2 • Frequency response: 20 Hz to 10 kHz • Measures the accumulated value of the DC and AC components in effective value, that is a true-RMS
		Temperature	Thermocouple: K, J, E, T, R, S, B, N, W (WRe5-26)
		Humidity	0 to 100 % RH – using the humidity sensor (option B-530)
	Filter (Low pass)		Off, Line (1.5 Hz), 5, 50, 500 Hz, 5, 50 kHz (at -3dB, -6dB/oct)
	A/D converter		16-bit (effective resolution: 1/40000 of the measuring full range)
	Maximum input voltage	Between (+) – (-) terminal	20 mV to 2 V range: 30 V DC, 5 V to 500 V range: 500 V DC
		Between channels (-) – (-) terminals)	60Vp-p
		Between channel – GND	60Vp-p
External input & output signal specifications	External input/output	Input	Logic or Pulse (4 channels), Trigger or Sampling (1 channel)
	External input/output	Output	Alarm (4 channels) or Trigger (1 channel) with Alarm (3 channels)
	Pulse measurement	Pulse count detection cycle	10 μs to 1 hr. (Set separately from analog signal sampling interval)
		Maximum pulse input	Maximum input frequency: 100 kHz, Maximum count number: 15 M count (24 bit counter)
		Measurement mode	Rotation: Counts the number of pulses per detection cycle and then converts measured value to rotation in rpm • Span: 0 to 500 M rpm/F.S.

			Accumulating: Accumulates the number of pulses count per detection cycle from the start of measurement • Span: 0 to 20 M count/F.S. (Span is set automatically)
			Instant: Counts the number of pulses per detection cycle • Span: 0 to 20 M count/F.S.
	External sampling input		Executes sampling of measurement signal with each external sampling signal • Maximum input frequency: 100 kHz (Time error: 1 μs or less)
	Output signal	Alarm output	Open collector (pull-up to 5 V with 10 kΩ resistor) • Maximum load is the 24 V and 100 mA
	Output signal	Trigger output	When a trigger is detected, output terminal releases approximately 500 μs width pulse (Low active)

Software specifications

スクロールできます

Item		Description
Supported OS		Windows11
Functions		Control GL980 and GL2000, Real-time data capture, Replay data, and Data format conversion
Supported device		1 unit of GL980 or GL2000
Settings control		Input condition, Capturing condition, Trigger/Alarm condition, other
Transfer of captured data	In memory capturing with GL2000	Transfer the captured data to a PC sequentially while data is saved in built-in RAM on GL2000 • Sampling interval: 1 μs to 1 min
Transfer of captured data	In real time capturing	Transfer the captured data to a PC while data is saved in built-in flash memory, SD or USB on GL2000 • Sampling interval: 1 ms to 1 min saved in GBD and CSV format
Displayed information		Analog waveform, Logic waveform, Pulse count waveform, Digital value
Display mode		Waveform in Y-T with digital values, Enlarged waveforms, Statistical calculation result values and history, XY graph
File operation		Converting data format to CSV from GBD binary with data between cursors or all data
Past data screen function		Displays the current data or past part of data by switching. Available at sampling speed 1 kS/s to 1 S/m (1 ms to 1 min sampling interval)
Statistical calculation		Maximum, Minimum, Average and Peak-to-peak (p-p) value during data capturing

Standard accessories

AC adapter with power cable
Ferrite core (attach to cable for radiation reduction)
Screws (M3.5) for input terminal
Tilt stand set (including mounting screws M4)
TO ENSURE SAFE AND CORRECT USE
Notice

Battery pack B-569 (option) Specifications

スクロールできます

Item	Description
Capacity	7.2V/2900mAh
Battery operating time	Approx. 3 hrs. in displayed signal (LCD: max. brightness) Approx. 5 hrs. in screen saver mode (no display) * When two battery packs are installed in GL2000. Condition: 1 sample per second (1 s), saving captured data to built-in Flash, use two fully charged battery packs, temperature is 25 ºC
Method of charging	Charging on GL2000
Charging time	Approx 10 hrs. (charging two batteries)
Other functions	• If an AC power failure occurs, it will automatically switch from the AC adapter to the battery pack. (AC adapter priority use) • When the voltage of the battery pack reaches low, the measurement is automatically stopped after saving data file preserving the accumulated data.

Humidity Sensor B-530 (option) Specifications

スクロールできます

Item	Description
Allowable temperature range	-25～80℃
Allowable humidity range	0～100％ RH
Relative humidity measurement accuracy	±3％ RH（5～98％ RH at 25℃）
Method	Capacitance method
Relative humidity measurement accuracy (5 to 98%)	Measurement environment	Measurement accuracy
	0～10℃	±5％ RH
	10～20℃	±4％ RH
	20～30℃	±3％ RH
	30～40℃	±4％ RH
	40～50℃	±5％ RH
	50～60℃	±6％ RH
	60～70℃	±7％ RH
	70～80℃	±8％ RH
	* Measurement accuracy at 60℃ or more is a reference value.
Response time	15 sec. (90% response when membrance filter is installed)
Sensor output	DCO～1V
External dimensions	Φ14 x 80 mm (excluding cable)
Cable length	3ｍ
Sensor power source	DC+5V～+16V
Power consumption	approx. 4 mA

Dimensions

GL2000 External Dimensions with cover (rubber protector)

Scale : mm
Tolerance : +/- 5 mm

GL2000 External Dimensions

Software for high performance and easy operation
Allows connections of Graphtec’s midiLOGGER series

The GL-Connection software included with GL7000, GL2000, GL980,GL860 and GL260 can control devices.
It is an integrated application software for the GL series, the GL900, GL860, GL840, GL820, GL260, GL240 and GL220 can also be connected and controll

Supported Models

GL7000 Plus / GL2000 / GL980
GL860 / GL840 / GL260 / GL240
GLT400 / GL900 /GL820/ GL220

Various measurement screens

The measurement signal can be displayed in various types of screens adapted to applications.

Multi-window function, measured signal can be displayed in various forms

Multi-window function

The GL-Connection software supports up to 2000 channels and up to 20 units of the GL series. It splits up to 4 windows and each window can display different format for easy monitoring signal in large channels.

When the unit of GL series is connected to the PC via Ethernet or USB, the GL-Connection software can manage a various information such as the data in capturing, data in the free running – displaying data without saving – and data in saved file.
The GL-Connection software can also display the data saved on the PC.

Tab function

The tab function allows you to manage the screen so that it can be intuitive and easy monitoring. Screen displayed in multi-window can split using the tab and selected items can be displayed. Items to be displayed can be set in detail, such as the GL body level, individual input module level, the specified channel, and other settings.

Copy of the entire tab

Copy of the channel

Move of the tab

Cursor synchronization

Release of remote lock of GL7000

Integrated application software for the GL series

When the software is used with the GL7000, it can be controlled and displayed the data including the FFT measurement. When other GL series is used, the software has mainly the waveform viewing function and have also the function to control basic items. Data captured by other GL series is compatible with the GL-Connection and APS software.

Connection of multiple units and the integrating function of the saved data

GL-connection software will be able to manage multiple units in a mixed condition of the GL series. Data integration function allows you to understand the overall situation immediately by creating single file at the same time axis from multiple data file saved by each unit.

スクロールできます

Connection method	Model	Model mixed	Control of Start/Stop	Data integration
1.Multiple unit connection	GL7000 Plus GL2000 GL980 GL860 GL840 GL260 GL240 GLT400	Yes	It make operation for each unit.	It makes manually after completing the data capture.
2.Link connection (simultaneous)	GL7000 Plus GL2000 GL980 GL860 GL840 GL260 GL240 GLT400	Yes	All units make the action in a single operation. * The timing of the action is maybe synchronized.	It makes automatically after completing the data capture. It can also make manually.
3.Link connection (synchronous) * Sync cable is used to connect each unit.	GL7000 Plus	No	All units make the action with full synchronization in a single operation.	It makes automatically after completing the data capture. It can also make manually.
4.Mixed connection, mixing of No.1 to No.3	GL7000 Plus GL2000 GL980 GL860 GL840 GL260 GL240 GLT400	Way of operation or action vary by type of connection that is the No.1 to No.3. * Full synchronization can be made when the sync cable is used in the GL7000.

データ結合の流れ

The integrated file cannot be created when it exceeds 100 units or 100 channels (analog channel + logic channel).
Data will be integrated with using fastest sampling speed when the sampling speed in each file is different.
The data format in integrated data file is the GL7000 format even if GL series is included to capture the data.

Main function of software

スクロールできます

Item			Description
GL-Connection (version 2.0 or later) GL260 (v.2.60 or later) GL860 (v.2.70 or later) *GLT400 (v.2.50 or later)	Connection	Supported model	GL7000, GL2000, GL980 GL900-4/-8 (Firm. v. 3.01 or later) GL860 GL840 (Firm. v. 1.21 or later) GL820 (Firm. v. 1.08 or later) GL260 GLT400 GL240 (Firm. v. 1.21 or later) GL220 (Firm. v. 1.06 or later)
		Max. number of unit	20
		Max. number of channel	2000
		Mixing the USB & LAN	Possible
	Display	Splitting of screen	Up to 4 screens
	Display	Group function	Up to 20 groups
GL980_2000-APS	Connection	Supported model	GL2000 / GL980
		Max. number of unit	1
		Max. number of channel	4 or 8
		Mixing the USB & LAN	N/A
	Display	Splitting of screen	No, single screen
	Display	Group function	N/A
GL100_GL240_GL840-APS	Connection	Supported model	GL840 / GL240 / GL820 / GL220 / GL100
		Max. number of unit	10
		Max. number of channel	1000
		Mixing the USB & LAN	Possible
	Display	Splitting of screen	No, single screen
	Display	Group function	Up to 4 groups
GL28-APS	Connection	Supported model	GL860 / GL840 / GL260 / GL240
		Max. number of unit	10
		Max. number of channel	1000
		Mixing the USB & LAN	Possible
	Display	Splitting of screen	No, single screen
	Display	Group function	Up to 4 groups
GL220_820-APS	Connection	Supported model	GL820 / GL800 / GL220 / GL200A
		Max. number of unit	10
		Max. number of channel	500
		Mixing the USB & LAN	N/A
	Display	Splitting of screen	No, single screen
	Display	Group function	Up to 4 groups
GL900-APS	Connection	Supported model	GL900-4 / GL900-8
		Max. number of unit	1
		Max. number of channel	4 or 8
		Mixing the USB & LAN	N/A
	Display	Splitting of screen	No, single screen
	Display	Group function	N/A

Supported model and condition of connection

スクロールできます

Supported model	Connected by USB	Connected by LAN	Wireless LANN	Notice
GL7000	Yes	Yes	N/A	(1) GL series up to 20 units (2) Up to 2000 channels
GL2000 / GL980	Yes	Yes	N/A
GL860	Yes	Yes	Yes ^※
GL840	Yes	Yes	Yes ^※
GL260	Yes	N/A	Yes ^※
GL240	Yes	N/A	Yes ^※
GLT400	Yes	Yes	Yes ^※
GL900	Yes	Yes	N/A
GL820	Yes	Yes	N/A
GL220	Yes	N/A	N/A

using B-568 option.
B-568 is available in limited region.

Sampling Limits

High speed sampling is limited by the number of recording channels, connected modules, and the recording destination, etc. Even within the following limits, transmission may be incomplete due to transmission delays with multiple module connections, especially with LAN connections. If this occurs, please reduce the sampling rate. For more details on the GL device limits, please refer to the main module user’s manual on CD-ROM.

GL7000

スクロールできます

Name	Explanation
Module-based limits (GL device limits)	Voltage module	1ms
	Voltage / Temperatuer module	10ms
	High Speed Voltage / High Voltage module	1μs
	DC Strain / Charge module	10μs
	Logic / Pulse module	Logic: 1 µs / pulse: 100 µs
Recording destination-based limits (GL device limits)	Internal RAM	1ms
	Internal flash	1ms
	SD card	1ms
	SSD module	1 to 2 modules:1 µs; however, the pulse runs only until 8ch 3 to 4 modules: 2 µs; however, the pulse is only until 16ch Over 5 modules: 5 µs
Main module recording format-based limits (GL device limits)	GBD (binary)	1μs
	CSV (Text)	10ms
Calculation function-based limits (GL device limits)	100 ms * The GL device’s calculation function cannot be used with this application. 　There is no calculation function in this application.
Ring recording-based limit. (GL device limits)	Ring recording-based limit. (GL device main module limits) When ring recording is on:100ms (Only when Internal Flash, SD card, SSD module)
Transmission-based limits (Application limits)	There are estimated sampling settings for PC recording depending on the volume of data communication. * When connecting through an existing network such as a LAN connection, communication may not be possible within the following limits. In such a case, please use a USB connection, or set a lower sampling rate. Estimated sampling rates
	USB connection	GBD (binary) format	1ms/5Unit
	USB connection	CSV (text) format	1ms/5Unit
	LAN connection	GBD (binary) format	1ms/5Unit
	LAN connection	CSV (text) format	1ms/5Unit

GL860、GL840、GL260、GL240、GLT400、GL820、GL220

スクロールできます

Name	Explanation
Limitations by amplifier (Limitations of the GL module side)	Number of CH available	Fastest sampling
	1	10ms
	2	20ms
	3～5	50ms
	6～10	100ms
	11～20	200ms
	21～50	500ms
	51～100	1s
	101～200	2s
	* The number of channels of the GS/WL sensors is not included
Main module recording format-based limits (GL device limits)	GBD (binary)	10ms～
	CSV (Text)	100ms～ (※GL860、GL840、GL260、GL240は10ms～)

GL2000、GL980

スクロールできます

Name	Explanation
Recording destination-based limits (GL device limits)	Internal RAM	1µs
	Internal flash	1ms
	USB memory	1ms
Main module recording format-based limits (GL device limits)	GBD (binary)	1ms～
	CSV (Text)	1ms～

GL900

スクロールできます

Name	Explanation
Recording destination-based limits (GL device limits)	Internal RAM	10us
	Internal flash	1ms
	USB memory	1ms
Main module recording format-based limits (GL device limits)	GBD (binary)	1ms～
	CSV (Text)	10ms～

Functions

スクロールできます

Item	Description
Module Settings List	Settings of multiple modules can be displayed simultaneously, and setting conditions can now be saved as CSV data.
Remote Lock On/Off Feature	Setting operation is available on GL7000 under control of GL-Connection.
Statistics / Display	Display statistical calculation result. Capturing data: Maximum, Minimum, Peak or Average Replaying data: Maximum, Minimum, Peak, Average or RMS in between cursors
Check-sum function	It is a function to check data file consistency. The check-sum code is recorded into the file when data file is created by the GL unit. When the content of the file is changed by someone, the check-sum generated from the file does not match with the recorded check-sum, which indicates that the file has been tampered with. * This software and the firmware on the GL unit need to be a version that supporting the check-sum function.
File operation	Converts binary data to the CSV data (specific period, all data in one file, multiple files), Creates a new file with compression or by consolidating multiple files.
Search function	Search any point on the data. Level: Specific level in any channels Alarm: Occurred alarm in any channel Time: Beginning, center, end of the data, Trigger point, Specific time (absolute, relative), Specific number
Warning function	Send e-mail to the specified address when the alarms occur

PC measurement with standard PC software included (GL980_2000-APS)

There are two types standard software for GL2000 and GL980, the PC software GL980_2000-APS can control GL2000 or GL980 and display measured data, the high-performance software GL-Connection has advanced functions and be used with other device of GL series.

PC measurement with standard PC software included (GL980_2000-APS)

Multiple measurement screens including Y-T waveform, XY chart

Y-T display

Recorded signal is displayed in waveform (Y-T) and digital value for each channel.

Y-T display (Zone mode)

Screen is divided into multiple zone, and channels can be assigned to each zone.

XY display

Four groups of XY charts are displayed.

Easily Connect to the GL2000/GL980 with Quick Set Up Conditions

Convenient features from the GL980_2000-APS software

File combine and bind function

Superimpose: Data or file recorded on another unit or time can be imported as additional channels when using a SUPERIMPOSE function.
Link: Captured data in multiple files are connected and saved as new file. It is helpful in reviewing data captured with relay mode.

* Measurement parameters of each file must be the same.

Direct Excel function

The GL980_2000-APS software executes recorded data into a file on PC in real time and exports to a specified Excel file at the same time.
This is a valuable tool in creating report requiring post-process calculation with Excel software.。

Printing function

The waveform of the playback data can be printed using a default printer. Printing range of the waveform can be set between cursors or all waveforms.